D'Link Router setup via dlinkrouter.local wizard?

If you long to set up your D-Link Ultra AC5300 Tri-band router, go for a browser-based setup process. The first requirement is to go for the setup process, connect your D-Link AC5300 Ultra router to the power supplying source. Connect your computer or the PC to the WIFI network name also called SSID of your network. This is your 5GHz antenna's network. www.dlinkrouter.local login also supports another network with the same name that is 2.4 GHz. If it is your first-time connection to this network, it will not have any security requirements. No password is needed to go ahead.

Important Notes: -

Collect all necessary information about your D-link Ultra AC5300 tri-band router.

You can call your internet service provider to get the required Dlink router login details.

Always go for wired Ethernet connection while doing the entire setup.

After supplying power to your router, check the LED status. It should be solid.

When you take out the router from the box, note down the username, password, and IP address.

Pro Tips: -

Before you go for setup, place the router to an adequate position or in the center of your house.

Place your D’link router at least three feet above from the ground to get optimal signals.

Connect your router and the modem through the WAN ports. And connect the computer to the router through the LAN ports.

Steps to install D’link Ultra AC5300 using a dlinkrouter.local web page

Launch a web directory on your device, communicating to the router and enter the IP address 192.168.0.50. You can also type the web domain http://dlinkrouter.local or dlinkrouter.local and click the enter key.

You have redirected to the page where you need to enter the default login credentials if not changed.

Once you are on the login or the authority verification page, enter admin in the field of username, and password in the password field. In the end, you should tap on the Login tab.

The main Dlink Ultra AC5300 router configuration page will appear here. Scroll up and visit the setup option.

You can now see the available options with many WIFI network names. You have to opt for the option that matches your network name only.

Here you will be asked to enter an appropriate password and then tap on the 'Next' key.

On the appeared page, you can change, modify or replace the username and password of your 2.4 GHz and 5 GHz networks respectively.

Click on next. Enter the Admin's username and password for added security. In this way, one can never mess with your router’s configurations.

Again tap the next option, and you get all the required settings. Once confirmed, you should click on the 'Finish' button to end the www.dlinkrouter.local setup process.

Your Dlink Ultra AC5300 router will reboot in 2 minutes and be prepared to connect your devices waiting for a WIFI network for a long time.

D’link AC5300 setup through the WPS button

Before setup instructions:

Make sure your router is powered on properly. Use the power adapter to connect your router to the electric outlet. The device to which you want to synchronize the router should have the same WPS button on it. Press the WPS button on both the devices within two minutes. In this process, the user is not required to use the web URL dlinkrouter.local to connect your device to the internet.

Make sure that you have positioned your router in the center of your house.

Don't forget to connect your Dlink router local to the power source.

Press the WPS button available on either side of your router.

Without any delay, press the WPS button on the modem or the computer.

The entire course of action should happen within two minutes.

Wait for the green LED to turn solid white.

Once your router establishes a connection with your modem, the LED will light solid green.

Now you are free to position the router in a location where you have less or no WIFI coverage.

The SSID is the WIFI username of your Dlink router wireless network.

All devices connected to the network have the same SSID to communicate on the Dlink Router.

Steps to replace the username and password for the D’link AC5300 router

Step 1: Open up a web browser and type the default gateway http://dlinkrouter.local or the IP address of your D-Link Router and click enter.

Step 2: The default username and password are already given below the firmware version of your Dlink router.

Step 3: The default username is used by most of the Dlink router login users in the admin.

Step 4: The default password column is left blank or in some cases, you may use the paraphrase password only.

Step 5: Click the wireless section on the left side of your computer's screen.

Step 6: Here you see the SSID field. Remove the previous SSID, and then enter that one you wish to have.

Step 7: Tap the apply button and then click to save the new settings on your computer.

You may choose to have a separate or the same password for both the wireless networks. The greatest benefit of choosing a 2.4 GHz wireless band is you have a greater range but slower internet speed whereas the 5 GHz wireless band has a shorter range but faster internet speed.

CONCLUSION

Congratulations! You have done the entire setup, login, and password change procedures successfully. To have a secured wireless network and internet sharing without any fear, go for D-Link routers, modems, and wireless range extenders. Dlinkrouter.local lets you enjoy uninterrupted video streaming anywhere you are.